Home > Mining Machinery > 500 Tph Stone Crusher Plant: Configuration, Capacity, and Selection Guide

500 Tph Stone Crusher Plant: Configuration, Capacity, and Selection Guide

Author: Justin

Oct. 27, 2026

12 0

500 Tph Stone Crusher Plant: Configuration, Capacity, and Selection Guide

A 500 Tph stone crusher plant is a crushing and screening system designed around a nominal throughput target of 500 metric tonnes per hour. A common starting configuration uses a primary jaw crusher, secondary cone or impact crushing, vibrating screens, and conveyors, with the final arrangement selected for the feed material and required products. The target is not a guaranteed hourly output: actual production depends on feed size, rock properties, product specifications, equipment selection, and operating conditions. Buyers should define these factors before comparing plant quotations.

If you are looking for more details, kindly visit our website.

Who This Guide Is For

This guide is for quarry owners, mining project teams, contractors, and procurement professionals assessing a high-capacity aggregate plant. It can help structure an initial equipment brief, compare process options, and prepare useful questions for potential suppliers. It is not a substitute for a site-specific process design or a supplier’s technical proposal based on tested material data.

What a 500 Tph Plant Includes

Basic process and equipment

A stone crushing plant turns run-of-mine or quarry feed into one or more specified aggregate products. Material typically passes through a feed system, primary crusher, secondary and sometimes tertiary crushing stages, screening equipment, and conveyors. Screens separate material by size; oversize can be returned for further crushing when the process design includes a closed circuit.

The plant’s equipment must work as a system. A crusher with sufficient individual capacity will not deliver the plant target if its feeder, screens, conveyors, or transfer points restrict the flow. Layout, stockpile arrangements, dust management, maintenance access, and electrical and control systems also affect project practicality and operating continuity.

Common configuration options

Process stage Typical equipment Selection consideration
Feed and primary crushing Hopper, vibrating feeder, jaw crusher Feed dimensions, rock strength, and the required reduction ratio
Secondary crushing Cone crusher or impact crusher Material abrasiveness, particle shape, and target product sizes
Final sizing Vibrating screens and, where needed, tertiary crushing Number of saleable products and grading requirements
Material handling Transfer chutes, conveyors, and stockpile equipment Plant layout, transfer capacity, and maintenance access

A jaw-and-cone arrangement is often considered for hard, abrasive rock, subject to material testing and product requirements. An impact-based configuration may be considered where the feed and desired particle shape make it appropriate, but wear costs should be evaluated for abrasive stone. Some projects use a tertiary stage, such as a cone or vertical shaft impact crusher, when the required grading or shape cannot be achieved with the initial stages alone.

Capacity: What 500 Tph Means in Practice

“500 Tph” can describe a design or rated capacity under specified conditions; it does not by itself define a plant’s saleable output. The operating result depends on factors such as feed gradation, moisture and clay content, crusher settings, screen efficiency, recirculating load, planned maintenance, and interruptions in upstream or downstream operations. Ask suppliers to state the assumptions behind any capacity figure and clarify whether it refers to feed rate or finished product.

For preliminary planning, an illustrative calculation helps show why rated and realized output differ. If a plant is assumed to run at 500 tonnes per hour during operation and is productive for 85% of scheduled time, the simple average is 425 tonnes per scheduled hour (500 × 0.85). The 85% figure here is an example, not a standard availability promise or a prediction for a specific project.

Define feed and product requirements

Before equipment sizing, provide the supplier with representative information about the feed, including maximum lump dimensions, size distribution, rock type, and any known abrasiveness or moisture concerns. Also list each required product fraction and its applicable grading or end-use requirements. For example, a brief might identify products such as 0–5 mm, 5–20 mm, and 20–40 mm, but those illustrative size bands should be replaced with the project’s actual specifications.

DAHONGLI are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

Changes in the product mix can alter screen selection, crusher settings, and the amount of material recirculated through the plant. A design intended to maximize one coarse product may not suit a project that needs several tightly controlled fractions. Ask for a process flow diagram and a capacity estimate tied to the proposed feed and product assumptions.

How to Select a Suitable Configuration

Use a step-by-step selection framework

  1. Document the material. Gather geological or laboratory information where available, and describe feed dimensions, hardness, abrasiveness, moisture, and fines or clay content.
  2. Set the product brief. Specify required fractions, grading tolerances, expected product split, and whether fines or manufactured sand are part of the project.
  3. Confirm the operating target. Clarify whether 500 Tph is a peak feed rate, a sustained operating target, or a finished-product requirement, and state planned operating hours and shifts.
  4. Review the process design. Compare primary and secondary crusher options, screening stages, recirculation paths, and provisions for bypassing or separating fines.
  5. Check the site and interfaces. Provide available footprint, elevation constraints, power supply details, access routes, and the relationship to existing quarry or downstream equipment.
  6. Compare whole-plant proposals. Review included equipment, exclusions, wear parts, controls, commissioning scope, documentation, and service arrangements—not just the main crusher model.

Match the plant to the application

Hard, abrasive materials call for careful assessment of crushing chamber selection, wear-part consumption, and maintenance access. Softer or less abrasive material may allow different crusher choices, but the product shape and grading still need to be verified. For mixed feed or variable quarry conditions, discuss how the plant will handle changes in feed size and composition without assuming that one setting will suit every operating condition.

A fixed plant may suit a long-term site where foundations, utilities, and permanent material routes can be planned. A mobile or modular arrangement may be considered when relocation, phased installation, or site access is a priority. The right choice depends on project duration, transport constraints, layout, and the scope of civil works; it cannot be determined from throughput alone.

Pricing, MOQ, and Lead Time

The price of a 500 Tph plant depends on its process scope and project conditions rather than the headline capacity alone. Key cost drivers can include crusher types and quantities, screening area, conveyors, electrical and control systems, structural steel, dust-control provisions, installation scope, and the inclusion of spare and wear parts. A comparable quotation should clearly separate included equipment from optional items and site-side responsibilities.

For a complete plant, minimum order quantity is usually a matter of project scope and commercial agreement, not a universal equipment rule. Lead time should be confirmed after the configuration, technical interfaces, and order requirements are defined. Ask the supplier to state the production and delivery basis, what information is needed to confirm the schedule, and which activities—such as foundations, utilities, or erection—are outside the quoted scope.

Supplier Evaluation Checklist

  • Does the proposal explain the assumptions behind the stated throughput?
  • Does it show a process flow diagram, equipment list, and expected product routes?
  • Are feed limits and required product sizes addressed explicitly?
  • Are power, foundations, installation boundaries, and site interfaces identified?
  • Does the quotation specify wear parts, recommended spares, controls, and documentation?
  • Can the supplier explain commissioning, operator guidance, and after-sales support for the proposed scope?

At DAHONGLI, we recommend sharing feed and product data, site constraints, and the intended operating schedule before requesting a final plant configuration. This gives our mining machinery team a clearer basis for discussing crusher selection, screening, conveying, and project interfaces. Buyers should request a written proposal that distinguishes design assumptions from confirmed scope and identifies any information still needed for engineering review.

Key Takeaways and Next Steps

A 500 Tph stone crusher plant is a coordinated crushing and screening system, not simply a single machine rated at 500 tonnes per hour. The suitable configuration depends on the feed material, finished-product requirements, operating conditions, site layout, and the definition of the capacity target. Capacity calculations and example product sizes are planning references only; a project-specific proposal should confirm the relevant assumptions.

To move from initial assessment to supplier comparison, prepare a material description, product-size schedule, operating target, site information, and preferred project scope. Then ask each supplier for a process diagram, capacity basis, equipment list, exclusions, and support details. Contact DAHONGLI with these project inputs to discuss a configuration and obtain a quotation tailored to your application.

Want more information on 500 Tph Stone Crusher? Feel free to contact us.

Comments

0